Category: compressor

Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V

Air-Compressor-For-Train-Horns-Air-Pressure-Supply-Kit-Silver-With-1-4-NPT-12V-01-olpu
Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V
Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V
Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V
Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V
Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V

Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V
Description: The silver maintenance free heavy-duty air compressor is rated at 200psi and is designed for any high-pressure on-board air system or other applications requiring air pressure supply. The perfect kit helps to save the power of the air compressor. The unit is equipped with standard 1 / 4 NPT stainless steel braided lead hose and mounting hardware. Applicable to all vehicles equipped with 12V system. Included in this kit: 1 200PSI air compressor with 1/4 NPT stainless steel braided leader hose mounting hardware Specification.
Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V
Continue Reading

Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V

Air-Compressor-For-Train-Horns-Air-Pressure-Supply-Kit-Silver-With-1-4-NPT-12V-01-yvow
Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V
Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V
Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V
Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V
Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V

Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V
The silver maintenance free heavy-duty air compressor is rated at 200psi and is designed for any high-pressure on-board air system or other applications requiring air pressure supply. The perfect kit helps to save the power of the air compressor. The unit is equipped with standard 1 / 4 NPT stainless steel braided lead hose and mounting hardware. Applicable to all vehicles equipped with 12V system. Included in this kit. 1 200PSI air compressor with 1/4 NPT stainless steel braided leader hose. Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V. 1 200PSI air compressor with. 1/4 NPT stainless steel braided leader hose. Type: 200PSI black air compressor. Thread: 1/4 NPT stainless steel braided leader hose. Working Voltage:12 Volt. Package Size(inch):14.29.87.4. 11″(L)×3.9″(W)×6.5(H). Max Amp Draw:23 Amps. Max Working Pressure:200 PSI. Do not attempt to disassemble, repair or customize this product. Avoid setting up any parts of this product where there is a risk of falling off or risk of coming in contact with water. Never leave this product unattended during use. Intended for use by adults only. During and immediately after use, avoid touching any part of the compressor with bare hands as it is very hot during such periods. Avoid sounding the air horn when in close range to your ear(s) or the ear(s) of others. Avoid use of product near flames, explosive materials, aerosol products or oxygen devices. Be sure to pump nothing other than atmospheric air. It is important to determine the maximum air pressure for any tool or attachment before using it. Air sprayer or nozzle should always be pointed away from any part of the body. The compressor has Thermal Overload Protection, if this protection activates, cut off the source of power and let the unit cool down for about 30 minutes. This will reset the system and allow you to safely resume use of the air compressor. Make sure your battery ground is detached before you begin. Set the horn up for use only in areas with adequate ventilation. Employ equipment for eye protection during drilling operations. Ensure that your air system has no pressure before you begin. The specific voltage requirement for this horn system is 12 volt DC, therefore installation must be done to a DC power source of 12 volts. Determine a dry place to mount your compressor. If you have chosen to install in the engine compartment, you should mount it as close to the front as possible to allow for maximum flow of air around compressor and also to avoid heat from the exhaust. IMPORTANT: Never attach the compressor to any plastic or other flexible material. For optimal results, the compressor should be placed as close to the battery as possible. This will reduce the amount of wiring needed. Avoid placing compressor near flammable liquids. If you are planning to move compressor’s air intake to an area other than where the compressor was installed, make sure your placement allows for the airline to be routed from the air inlet of the compressor to the remote inlet air filter. Mark the spots for the holes with the mounting base as a guide and then drill. Make sure the compressor is secured. To enhance performance and make sure the battery of your vehicle doesn’t discharge, keep the engine running while the compressor is being used. Connect the stainless steel braided hose of the compressor to the tank’s inlet port. IMPORTANT: The tank’s inlet port must be 1/4 N. The check valve is an important part of the air compressor and has only one function: to let air flow from one side to the other, in this case from the compressor to the tank, while blocking air flow in the opposite direction. IMPORTANT: When installing the braided hose do not rotate or remove the inline check valve located at the end of the hose on the side that connects to the air tank. Doing so will damage its seals and will result in damage to your air compressor. Using a compatible remote air filter installation kit (NOT PROVIED) your compressor’s air intake can be installed in an area other than where the compressor was installed. The red wire of the compressor should be connected to (+) 12-volt power source. IMPORTANT: To prevent the compressor from over running and possible damage due to an air leak, connect the compressor’s red wire to a power source in the vehicle that only gets power when the vehicle’s ignition is on. Recommended connection points are: windshield wiper motor, blower motor or an accessory terminal on the fuse panel. Make sure to use wire that is as heavy as the wire of the compressor and to use the included fuse for circuit’s protection. Attach the black wire to any of the Pressure Switch’s connections located on the air tank. The remaining Pressure Switch connection should be attached to ground. Secure the end to any metal body or to the negative side of the vehicle’s battery. The ground connection should be rust and paint free. Your compressor is now set for use and will turn on automatically when air pressure in the air tank falls. When air pressure reaches maximum PSI, it will turn off. If the compressor fails to reach the maximum air pressure of the tank, which is the Pressure Switch’s cut OFF pressure, check all air connections for leaks. While the compressor is pumping, use soapy water or any bubble solution to perform this check. In case the leak remains after tightening, re-apply thread sealant. Make sure that electrical and fitting connections are regularly inspected, cleaned and tightened when needed. Make sure mounting screws are regularly tightened if needed. Compressor features a washable air filter which should be cleaned using any mild form of liquid soap every two months if it gets dusty. Just remove the front cover of the filter’s housing to reach it. Replacement time frames depend on the operating environment and how often it is used. Clean dirt and dust from heat spreader and motor housing of the compressor. The motor of the air compressor has a maintenance-free lasting lubricant. SOLUTIONS TO COMMON ISSUES. Solution 1: Check all switches to make sure they are ON. Solution 2: Check the fuse; if blown, disconnect compressor from power and replace the fuse. Solution 3: Allow compressor to cool off for 30-60 minutes. Solution 4: Check pressure switch, replace if damaged or inoperable. Issue: Excessive moisture in horn or safety valve. Solution 1: Depressurize and drain the tank. Solution 2: Relocate the on-board air system to a drier location. Issue: Continual cutting-off of Thermal overload protection. Solution 1: Relocate the on-board air system to a drier, cooler location. Solution 2: Replace the compressor. Issue: Excessive vibration or noise. Solution 1: Tighten system components. Issue: Loss of pressure of tank when compressor is shut off. Solution 1: Tighten drain cock. Solution 2: Examine air and check valves and replace if damaged or leaking. Solution 3: Use soap and water solution on air connections, and tighten connections or repair leaks where needed. Olution 4: Replace safety valve if present in the tank, it may be defective. Issue: Compressor runs continuously and has low air flow. Solution 1: Decrease the frequency of use. Solution 2: Use soap and water solution on air connections, and tighten connections or repair leaks where needed. Solution 3: Clean or replace the air filter element if it is clogged. Solution 4: Replace compressor. Make sure you never attempt to disassemble this horn kit’s electrical components. Never use your bare hands to any part of the compressor immediately after or during use. Avoid operating this product in an area with risk of falling or submergence into a liquid (water). Do not reach out for or touch any component that has fallen or been submerged into water. Make sure you set up in areas with good ventilation. Never sound the air horn anywhere near your ear(s) or that of another person. Make sure your battery ground is detached before getting your installation started. The specific voltage requirement for this horn kit is 12 volt DC, therefore installation must be done to a DC power source of 12 volts. 14.29.87.4. The images shown are not the actual item and are for your reference only. Service transit time is provided by the carrier and excludes weekends and holidays. Transit times may vary, particularly during the holiday season. There are NO EXCEPTIONS! FEEDBACK IS VERY IMPORTANT TO US. It is impossible to address issues if we do not know about them! Transfer Case Shift Motor. Secondary Air Injection Pump. Center Console Organizer Parts. ATV Brake Master Cylinder. Mass Air Flow Sensor. Splash Guards & Mud Flaps. Brake Disc Rotors and Pads. Brake Pads & Rotor & Caliper. Brake Pads & Calipers. Light Bar Mount Bracket. Cylinder Head Gasket Sets. 4 Pcs wheel hub bearing. UTV & ATV Brake System Parts. Kevlar Carbon Brake Pads. Pivot Brake Clutch Lever. Cooling Fans and Fan Clutches. Brake Rotors Pads & Drum Shoe. Rear Window Louver Cover. C Notch & Flip Kit. Other Golf Cart Parts. Body Side Door Moulding. Motorcycle Carburetor & Parts. Variable Timing Solenoid(VVT). Cylinder piston gasket kit. Wheel Hub Bearing Knuckle. Ignition Coil & Spark Plug Set. Oxygen O2 02 Sensor for 04-08 Acura TSX 03-07 Honda Accord 2.4L Downstream. 2pcs 1 Upstream & 1 Downstream Oxygen Sensor For 96-02 Honda Accord 2.2L 3.0L. For Ford Ranger 2.3L 2.5L F150 Expedition Lincoln Mercury FD487 Ignition Coil. 4PCS Ignition Coil For Toyota Camry RAV4 Highlander Solara Scion 2.4L UF333. 6x Ignition Coils for Nissan Frontier Pathfinder Altima Maxima 3.5L 4.0L UF349.
Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V
Continue Reading

Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V

Air-Compressor-For-Train-Horns-Air-Pressure-Supply-Kit-Silver-With-1-4-NPT-12V-01-pgmb
Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V
Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V
Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V
Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V
Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V

Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V
The silver maintenance free heavy-duty air compressor is rated at 200psi and is designed for any high-pressure on-board air system or other applications requiring air pressure supply. The perfect kit helps to save the power of the air compressor. The unit is equipped with standard 1 / 4 NPT stainless steel braided lead hose and mounting hardware. Applicable to all vehicles equipped with 12V system. Included in this kit. 1 200PSI air compressor with 1/4 NPT stainless steel braided leader hose. Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V. 1 200PSI air compressor with. 1/4 NPT stainless steel braided leader hose. Type: 200PSI black air compressor. Thread: 1/4 NPT stainless steel braided leader hose. Working Voltage:12 Volt. Package Size(inch):14.29.87.4. 11″(L)×3.9″(W)×6.5(H). Max Amp Draw:23 Amps. Max Working Pressure:200 PSI. Do not attempt to disassemble, repair or customize this product. Avoid setting up any parts of this product where there is a risk of falling off or risk of coming in contact with water. Never leave this product unattended during use. Intended for use by adults only. During and immediately after use, avoid touching any part of the compressor with bare hands as it is very hot during such periods. Avoid sounding the air horn when in close range to your ear(s) or the ear(s) of others. Avoid use of product near flames, explosive materials, aerosol products or oxygen devices. Be sure to pump nothing other than atmospheric air. It is important to determine the maximum air pressure for any tool or attachment before using it. Air sprayer or nozzle should always be pointed away from any part of the body. The compressor has Thermal Overload Protection, if this protection activates, cut off the source of power and let the unit cool down for about 30 minutes. This will reset the system and allow you to safely resume use of the air compressor. Make sure your battery ground is detached before you begin. Set the horn up for use only in areas with adequate ventilation. Employ equipment for eye protection during drilling operations. Ensure that your air system has no pressure before you begin. The specific voltage requirement for this horn system is 12 volt DC, therefore installation must be done to a DC power source of 12 volts. Determine a dry place to mount your compressor. If you have chosen to install in the engine compartment, you should mount it as close to the front as possible to allow for maximum flow of air around compressor and also to avoid heat from the exhaust. IMPORTANT: Never attach the compressor to any plastic or other flexible material. For optimal results, the compressor should be placed as close to the battery as possible. This will reduce the amount of wiring needed. Avoid placing compressor near flammable liquids. If you are planning to move compressor’s air intake to an area other than where the compressor was installed, make sure your placement allows for the airline to be routed from the air inlet of the compressor to the remote inlet air filter. Mark the spots for the holes with the mounting base as a guide and then drill. Make sure the compressor is secured. To enhance performance and make sure the battery of your vehicle doesn’t discharge, keep the engine running while the compressor is being used. Connect the stainless steel braided hose of the compressor to the tank’s inlet port. IMPORTANT: The tank’s inlet port must be 1/4 N. The check valve is an important part of the air compressor and has only one function: to let air flow from one side to the other, in this case from the compressor to the tank, while blocking air flow in the opposite direction. IMPORTANT: When installing the braided hose do not rotate or remove the inline check valve located at the end of the hose on the side that connects to the air tank. Doing so will damage its seals and will result in damage to your air compressor. Using a compatible remote air filter installation kit (NOT PROVIED) your compressor’s air intake can be installed in an area other than where the compressor was installed. The red wire of the compressor should be connected to (+) 12-volt power source. IMPORTANT: To prevent the compressor from over running and possible damage due to an air leak, connect the compressor’s red wire to a power source in the vehicle that only gets power when the vehicle’s ignition is on. Recommended connection points are: windshield wiper motor, blower motor or an accessory terminal on the fuse panel. Make sure to use wire that is as heavy as the wire of the compressor and to use the included fuse for circuit’s protection. Attach the black wire to any of the Pressure Switch’s connections located on the air tank. The remaining Pressure Switch connection should be attached to ground. Secure the end to any metal body or to the negative side of the vehicle’s battery. The ground connection should be rust and paint free. Your compressor is now set for use and will turn on automatically when air pressure in the air tank falls. When air pressure reaches maximum PSI, it will turn off. If the compressor fails to reach the maximum air pressure of the tank, which is the Pressure Switch’s cut OFF pressure, check all air connections for leaks. While the compressor is pumping, use soapy water or any bubble solution to perform this check. In case the leak remains after tightening, re-apply thread sealant. Make sure that electrical and fitting connections are regularly inspected, cleaned and tightened when needed. Make sure mounting screws are regularly tightened if needed. Compressor features a washable air filter which should be cleaned using any mild form of liquid soap every two months if it gets dusty. Just remove the front cover of the filter’s housing to reach it. Replacement time frames depend on the operating environment and how often it is used. Clean dirt and dust from heat spreader and motor housing of the compressor. The motor of the air compressor has a maintenance-free lasting lubricant. SOLUTIONS TO COMMON ISSUES. Solution 1: Check all switches to make sure they are ON. Solution 2: Check the fuse; if blown, disconnect compressor from power and replace the fuse. Solution 3: Allow compressor to cool off for 30-60 minutes. Solution 4: Check pressure switch, replace if damaged or inoperable. Issue: Excessive moisture in horn or safety valve. Solution 1: Depressurize and drain the tank. Solution 2: Relocate the on-board air system to a drier location. Issue: Continual cutting-off of Thermal overload protection. Solution 1: Relocate the on-board air system to a drier, cooler location. Solution 2: Replace the compressor. Issue: Excessive vibration or noise. Solution 1: Tighten system components. Issue: Loss of pressure of tank when compressor is shut off. Solution 1: Tighten drain cock. Solution 2: Examine air and check valves and replace if damaged or leaking. Solution 3: Use soap and water solution on air connections, and tighten connections or repair leaks where needed. Olution 4: Replace safety valve if present in the tank, it may be defective. Issue: Compressor runs continuously and has low air flow. Solution 1: Decrease the frequency of use. Solution 2: Use soap and water solution on air connections, and tighten connections or repair leaks where needed. Solution 3: Clean or replace the air filter element if it is clogged. Solution 4: Replace compressor. Make sure you never attempt to disassemble this horn kit’s electrical components. Never use your bare hands to any part of the compressor immediately after or during use. Avoid operating this product in an area with risk of falling or submergence into a liquid (water). Do not reach out for or touch any component that has fallen or been submerged into water. Make sure you set up in areas with good ventilation. Never sound the air horn anywhere near your ear(s) or that of another person. Make sure your battery ground is detached before getting your installation started. The specific voltage requirement for this horn kit is 12 volt DC, therefore installation must be done to a DC power source of 12 volts. 14.29.87.4. The images shown are not the actual item and are for your reference only. Service transit time is provided by the carrier and excludes weekends and holidays. Transit times may vary, particularly during the holiday season. There are NO EXCEPTIONS! FEEDBACK IS VERY IMPORTANT TO US. It is impossible to address issues if we do not know about them! Transfer Case Shift Motor. Secondary Air Injection Pump. Center Console Organizer Parts. ATV Brake Master Cylinder. Mass Air Flow Sensor. Splash Guards & Mud Flaps. Brake Disc Rotors and Pads. Brake Pads & Rotor & Caliper. Brake Pads & Calipers. Light Bar Mount Bracket. Cylinder Head Gasket Sets. 4 Pcs wheel hub bearing. UTV & ATV Brake System Parts. Kevlar Carbon Brake Pads. Pivot Brake Clutch Lever. Cooling Fans and Fan Clutches. Brake Rotors Pads & Drum Shoe. Rear Window Louver Cover. Engine Splash Shield Guard. C Notch & Flip Kit. Other Golf Cart Parts. Body Side Door Moulding. Motorcycle Carburetor & Parts. Variable Timing Solenoid(VVT). Cylinder piston gasket kit. Wheel Hub Bearing Knuckle. Air suspension valve solenoid. Power+Heated Manual Telescoping Black For 2004-09 Dodge Durango Left Side Mirror. For 2005-08 Suzuki Forenza Reno Power Window Regulator Front RH LH w/ motor. L+R For 99-07 Ford F250/F350/F450/F550 Power Heated Turn Signal Tow Side Mirrors. 6x Ignition Coils for Nissan Frontier Pathfinder Altima Maxima 3.5L 4.0L UF349. For Ford Ranger 2.3L 2.5L F150 Expedition Lincoln Mercury FD487 Ignition Coil.
Air Compressor For Train Horns Air Pressure Supply Kit Silver With 1/4 NPT 12V
Continue Reading

150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4” Hose

150-PSI-Air-Compressor-for-Car-Truck-Train-Horns-Bag-Suspension-with-1-4-Hose-01-wlje
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose

150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
12V 150Psi Air Compressor 1/4 Hose Kit For Car Truck Train Horns Suspension Specification: Condition: Brand New!! Features: -Oil-less Design -Moisture and Dust Resistant -Anodized Aluminum Alloy Cylinder -Automatic Reset Thermal Overload Protector -Mounting Plates with Vibration Isolators -¼ NPT Stainless Steel Braided Leader Hose -Intake Filter Assembly -Insulated Wiring with Connectors Package Incldues: 1 x Air Compressor 4 x Flat Head Screws 8 x Mounting Pieces 4 x Nuts 4 x Small Steel Rings 1 x Rubber Ring 1 x Fuse 1 x Safety Valve Note: 1. We provide clear pictures, measurements where possible. Please check as much as possible to make sure the item is the one that you need. Please allow 0.5-1 inch difference due to manual measurement. There are no instructions included in this kit. We will provide help as much as possible. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts & Accessories\Interior Parts & Accessories\Steering Wheels & Horn Buttons”. The seller is “unopery” and is located in this country: CN. This item can be shipped worldwide.
  • Brand: Unbranded
  • Manufacturer Part Number: fQh8348613
  • Type: Compressor
  • Placement on Vehicle: Front,Rear
  • Manufacturer Warranty: 1 Year
  • Fitment Type: Direct Replacement
  • Horn Type: Electric
  • Color: Silver
  • Size: 21cm x 15.2cm (LxH)
  • Hose Length: 58cm
  • Voltage: 12V
  • Maximum Working Pressure: 150 PSI
  • Duty Cycle: 25% @ 100 PSI
  • Amperage Draw: 20A
  • Flow Rate: 1.9CFM @ 0 PSI

150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
Continue Reading

Air Compressor Kit For Car Train Horns Air Horn Air Suspension With 1/4 NPT

Air-Compressor-Kit-For-Car-Train-Horns-Air-Horn-Air-Suspension-With-1-4-NPT-01-qc
Air Compressor Kit For Car Train Horns Air Horn Air Suspension With 1/4 NPT
Air Compressor Kit For Car Train Horns Air Horn Air Suspension With 1/4 NPT
Air Compressor Kit For Car Train Horns Air Horn Air Suspension With 1/4 NPT
Air Compressor Kit For Car Train Horns Air Horn Air Suspension With 1/4 NPT
Air Compressor Kit For Car Train Horns Air Horn Air Suspension With 1/4 NPT

Air Compressor Kit For Car Train Horns Air Horn Air Suspension With 1/4 NPT
The silver maintenance free heavy-duty air compressor has a rated working pressure of 200psi, which is convenient and safe to avoid any possible safety accidents, maintenance free, and avoid being designed for any high-pressure on-board air system and other applications requiring air pressure supply. The unit is equipped with standard 1 / 4 NPT stainless steel braided lead hose and mounting hardware. Applicable to all vehicles equipped with 12V system. The package size is (inches) 14.2 9.8 7.4. Included in this kit. 1 200PSI air compressor with 1/4 NPT stainless steel braided leader hose. Air Compressor Kit For Car Train Horns Air Horn Air Suspension With 1/4 NPT. 1 200PSI air compressor with. 1/4 NPT stainless steel braided leader hose. Type: 200PSI black air compressor. Thread: 1/4 NPT stainless steel braided leader hose. Working Voltage:12 Volt. Package Size(inch):14.29.87.4. 11″(L)×3.9″(W)×6.5(H). Max Amp Draw:23 Amps. Max Working Pressure:200 PSI. Do not attempt to disassemble, repair or customize this product. Avoid setting up any parts of this product where there is a risk of falling off or risk of coming in contact with water. Never leave this product unattended during use. Intended for use by adults only. During and immediately after use, avoid touching any part of the compressor with bare hands as it is very hot during such periods. Avoid sounding the air horn when in close range to your ear(s) or the ear(s) of others. Avoid use of product near flames, explosive materials, aerosol products or oxygen devices. Be sure to pump nothing other than atmospheric air. It is important to determine the maximum air pressure for any tool or attachment before using it. Air sprayer or nozzle should always be pointed away from any part of the body. The compressor has Thermal Overload Protection, if this protection activates, cut off the source of power and let the unit cool down for about 30 minutes. This will reset the system and allow you to safely resume use of the air compressor. Make sure your battery ground is detached before you begin. Set the horn up for use only in areas with adequate ventilation. Employ equipment for eye protection during drilling operations. Ensure that your air system has no pressure before you begin. The specific voltage requirement for this horn system is 12 volt DC, therefore installation must be done to a DC power source of 12 volts. Determine a dry place to mount your compressor. If you have chosen to install in the engine compartment, you should mount it as close to the front as possible to allow for maximum flow of air around compressor and also to avoid heat from the exhaust. IMPORTANT: Never attach the compressor to any plastic or other flexible material. For optimal results, the compressor should be placed as close to the battery as possible. This will reduce the amount of wiring needed. Avoid placing compressor near flammable liquids. If you are planning to move compressor’s air intake to an area other than where the compressor was installed, make sure your placement allows for the airline to be routed from the air inlet of the compressor to the remote inlet air filter. Mark the spots for the holes with the mounting base as a guide and then drill. Make sure the compressor is secured. To enhance performance and make sure the battery of your vehicle doesn’t discharge, keep the engine running while the compressor is being used. Connect the stainless steel braided hose of the compressor to the tank’s inlet port. IMPORTANT: The tank’s inlet port must be 1/4 N. The check valve is an important part of the air compressor and has only one function: to let air flow from one side to the other, in this case from the compressor to the tank, while blocking air flow in the opposite direction. IMPORTANT: When installing the braided hose do not rotate or remove the inline check valve located at the end of the hose on the side that connects to the air tank. Doing so will damage its seals and will result in damage to your air compressor. Using a compatible remote air filter installation kit (NOT PROVIED) your compressor’s air intake can be installed in an area other than where the compressor was installed. The red wire of the compressor should be connected to (+) 12-volt power source. IMPORTANT: To prevent the compressor from over running and possible damage due to an air leak, connect the compressor’s red wire to a power source in the vehicle that only gets power when the vehicle’s ignition is on. Recommended connection points are: windshield wiper motor, blower motor or an accessory terminal on the fuse panel. Make sure to use wire that is as heavy as the wire of the compressor and to use the included fuse for circuit’s protection. Attach the black wire to any of the Pressure Switch’s connections located on the air tank. The remaining Pressure Switch connection should be attached to ground. Secure the end to any metal body or to the negative side of the vehicle’s battery. The ground connection should be rust and paint free. Your compressor is now set for use and will turn on automatically when air pressure in the air tank falls. When air pressure reaches maximum PSI, it will turn off. If the compressor fails to reach the maximum air pressure of the tank, which is the Pressure Switch’s cut OFF pressure, check all air connections for leaks. While the compressor is pumping, use soapy water or any bubble solution to perform this check. In case the leak remains after tightening, re-apply thread sealant. Make sure that electrical and fitting connections are regularly inspected, cleaned and tightened when needed. Make sure mounting screws are regularly tightened if needed. Compressor features a washable air filter which should be cleaned using any mild form of liquid soap every two months if it gets dusty. Just remove the front cover of the filter’s housing to reach it. Replacement time frames depend on the operating environment and how often it is used. Clean dirt and dust from heat spreader and motor housing of the compressor. The motor of the air compressor has a maintenance-free lasting lubricant. SOLUTIONS TO COMMON ISSUES. Solution 1: Check all switches to make sure they are ON. Solution 2: Check the fuse; if blown, disconnect compressor from power and replace the fuse. Solution 3: Allow compressor to cool off for 30-60 minutes. Solution 4: Check pressure switch, replace if damaged or inoperable. Issue: Excessive moisture in horn or safety valve. Solution 1: Depressurize and drain the tank. Solution 2: Relocate the on-board air system to a drier location. Issue: Continual cutting-off of Thermal overload protection. Solution 1: Relocate the on-board air system to a drier, cooler location. Solution 2: Replace the compressor. Issue: Excessive vibration or noise. Solution 1: Tighten system components. Issue: Loss of pressure of tank when compressor is shut off. Solution 1: Tighten drain cock. Solution 2: Examine air and check valves and replace if damaged or leaking. Solution 3: Use soap and water solution on air connections, and tighten connections or repair leaks where needed. Olution 4: Replace safety valve if present in the tank, it may be defective. Issue: Compressor runs continuously and has low air flow. Solution 1: Decrease the frequency of use. Solution 2: Use soap and water solution on air connections, and tighten connections or repair leaks where needed. Solution 3: Clean or replace the air filter element if it is clogged. Solution 4: Replace compressor. Make sure you never attempt to disassemble this horn kit’s electrical components. Never use your bare hands to any part of the compressor immediately after or during use. Avoid operating this product in an area with risk of falling or submergence into a liquid (water). Do not reach out for or touch any component that has fallen or been submerged into water. Make sure you set up in areas with good ventilation. Never sound the air horn anywhere near your ear(s) or that of another person. Make sure your battery ground is detached before getting your installation started. The specific voltage requirement for this horn kit is 12 volt DC, therefore installation must be done to a DC power source of 12 volts. 14.29.87.4. If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items. CARMASUSPENSIONS has the final power of interpretation of all the above Targeted Discount Terms and Procedures. Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. Virgin Islands, Northern Marianas, Guam are not deliverable. Which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. Promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise. Has the right to refuse any replacement requests. Fit for Ford F-100 150 250 350 Bronco 6 Suspension Steering Tie Rod Ends Kit. For 1999-06 Chevy + GMC 1500 Trucks 6-Lug 4×4 Complete Front Suspension Kit x13. Fits Ford F-250 F-350 Super Duty – 4WD 4×4 New 5x Complete Front Suspension Kit. For 2000-13 Chevy Impala 8PCS Front Lower Control Arm Sway Bar Tie Rod Ends Kit. For Ford Ranger & Explorer 4WD 10Pcs Front Control Arms Ball Joints Tie Rods Kit. 6 Front Lower Suspension Control Arms Set Fit For 01 02 Chrysler Town & Country. 4 set Fits 01-06 07 Dodge Caravan Front Lower Control Arms Sway Bar Link Kit. 6pcs Front Tie Rod Ends Ball Joints For Lincoln Town Car Marquis Crown Victoria. The item “Air Compressor Kit For Car Train Horns Air Horn Air Suspension With 1/4 NPT” is in sale since Tuesday, November 9, 2021. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts & Accessories\Interior Parts & Accessories\Steering Wheels & Horn Buttons”. The seller is “carmasuspensions” and is located in Ontario, California. This item can be shipped to United States.
  • UPC: Does not apply
  • Brand: ulikebatte
  • Manufacturer Part Number: UT169894S01
  • Type: Horn
  • Part Type: Air Compressor
  • Horn Type: High Pressure Air
  • Material: Metal
  • Fitment Type: Direct Replacement
  • Color: Silver
  • Manufacturer Warranty: 1 Year
  • Placement on Vehicle: Left
  • Package Size(inch): 14.2*9.8*7.4
  • Package Weight: 12.24LB
  • Voltage: 12V

Air Compressor Kit For Car Train Horns Air Horn Air Suspension With 1/4 NPT
Continue Reading

150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4” Hose

150-PSI-Air-Compressor-for-Car-Truck-Train-Horns-Bag-Suspension-with-1-4-Hose-01-qy
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose

150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
12V 150Psi Air Compressor 1/4 Hose Kit For Car Truck Train Horns Suspension Specification: Condition: Brand New!! Features: -Oil-less Design -Moisture and Dust Resistant -Anodized Aluminum Alloy Cylinder -Automatic Reset Thermal Overload Protector -Mounting Plates with Vibration Isolators -¼ NPT Stainless Steel Braided Leader Hose -Intake Filter Assembly -Insulated Wiring with Connectors Package Incldues: 1 x Air Compressor 4 x Flat Head Screws 8 x Mounting Pieces 4 x Nuts 4 x Small Steel Rings 1 x Rubber Ring 1 x Fuse 1 x Safety Valve Note: 1. We provide clear pictures, measurements where possible. Please check as much as possible to make sure the item is the one that you need. Please allow 0.5-1 inch difference due to manual measurement. There are no instructions included in this kit. We will provide help as much as possible. The item “150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4” Hose” is in sale since Saturday, October 23, 2021. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts & Accessories\Interior Parts & Accessories\Steering Wheels & Horn Buttons”. The seller is “unopery” and is located in Shenzhen. This item can be shipped worldwide.
  • Brand: Unbranded
  • Manufacturer Part Number: fQh8348613
  • Type: Compressor
  • Placement on Vehicle: Front,Rear
  • Manufacturer Warranty: 1 Year
  • Fitment Type: Direct Replacement
  • Horn Type: Electric
  • Color: Silver
  • Size: 21cm x 15.2cm (LxH)
  • Hose Length: 58cm
  • Voltage: 12V
  • Maximum Working Pressure: 150 PSI
  • Duty Cycle: 25% @ 100 PSI
  • Amperage Draw: 20A
  • Flow Rate: 1.9CFM @ 0 PSI

150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
Continue Reading

Air Compressor For Train Air Horns Air Suspension Kit Silver Heavy Duty With NPT

Air-Compressor-For-Train-Air-Horns-Air-Suspension-Kit-Silver-Heavy-Duty-With-NPT-01-sluw
Air Compressor For Train Air Horns Air Suspension Kit Silver Heavy Duty With NPT
Air Compressor For Train Air Horns Air Suspension Kit Silver Heavy Duty With NPT
Air Compressor For Train Air Horns Air Suspension Kit Silver Heavy Duty With NPT
Air Compressor For Train Air Horns Air Suspension Kit Silver Heavy Duty With NPT
Air Compressor For Train Air Horns Air Suspension Kit Silver Heavy Duty With NPT

Air Compressor For Train Air Horns Air Suspension Kit Silver Heavy Duty With NPT
The silver maintenance free heavy-duty air compressor is rated at 200psi and is designed for any high-pressure on-board air system or other applications requiring air pressure supply. The unit is equipped with standard 3 / 8 NPT stainless steel braided lead hose and mounting hardware. Applicable to all vehicles equipped with 12V system. Please read the installation instructions carefully. Included in this kit. 1 200PSI air compressor with 3/8 NPT stainless steel braided leader hose. Air Compressor For Train Air Horns Air Suspension Kit Silver Heavy Duty With NPT. 1 200PSI air compressor with 3. /8 NPT stainless steel braided leader hose. Thread: 3/8 NPT stainless steel braided leader hose. Working Voltage:12 Volt. Package Size(inch):14.210.27.1. 11″(L)×3.9″(W)×6.5(H). Max Amp Draw:23 Amps. Max Working Pressure:200 PSI. Do not attempt to disassemble, repair or customize this product. Avoid setting up any parts of this product where there is a risk of falling off or risk of coming in contact with water. Never leave this product unattended during use. Intended for use by adults only. During and immediately after use, avoid touching any part of the compressor with bare hands as it is very hot during such periods. Avoid sounding the air horn when in close range to your ear(s) or the ear(s) of others. Avoid use of product near flames, explosive materials, aerosol products or oxygen devices. Be sure to pump nothing other than atmospheric air. It is important to determine the maximum air pressure for any tool or attachment before using it. Air sprayer or nozzle should always be pointed away from any part of the body. The compressor has Thermal Overload Protection, if this protection activates, cut off the source of power and let the unit cool down for about 30 minutes. This will reset the system and allow you to safely resume use of the air compressor. Make sure your battery ground is detached before you begin. Set the horn up for use only in areas with adequate ventilation. Employ equipment for eye protection during drilling operations. Ensure that your air system has no pressure before you begin. The specific voltage requirement for this horn system is 12 volt DC, therefore installation must be done to a DC power source of 12 volts. Determine a dry place to mount your compressor. If you have chosen to install in the engine compartment, you should mount it as close to the front as possible to allow for maximum flow of air around compressor and also to avoid heat from the exhaust. IMPORTANT: Never attach the compressor to any plastic or other flexible material. For optimal results, the compressor should be placed as close to the battery as possible. This will reduce the amount of wiring needed. Avoid placing compressor near flammable liquids. If you are planning to move compressor’s air intake to an area other than where the compressor was installed, make sure your placement allows for the airline to be routed from the air inlet of the compressor to the remote inlet air filter. Mark the spots for the holes with the mounting base as a guide and then drill. Make sure the compressor is secured. To enhance performance and make sure the battery of your vehicle doesn’t discharge, keep the engine running while the compressor is being used. Connect the stainless steel braided hose of the compressor to the tank’s inlet port. IMPORTANT: The tank’s inlet port must be 1/4 N. The check valve is an important part of the air compressor and has only one function: to let air flow from one side to the other, in this case from the compressor to the tank, while blocking air flow in the opposite direction. IMPORTANT: When installing the braided hose do not rotate or remove the inline check valve located at the end of the hose on the side that connects to the air tank. Doing so will damage its seals and will result in damage to your air compressor. Using a compatible remote air filter installation kit (NOT PROVIED) your compressor’s air intake can be installed in an area other than where the compressor was installed. The red wire of the compressor should be connected to (+) 12-volt power source. IMPORTANT: To prevent the compressor from over running and possible damage due to an air leak, connect the compressor’s red wire to a power source in the vehicle that only gets power when the vehicle’s ignition is on. Recommended connection points are: windshield wiper motor, blower motor or an accessory terminal on the fuse panel. Make sure to use wire that is as heavy as the wire of the compressor and to use the included fuse for circuit’s protection. Attach the black wire to any of the Pressure Switch’s connections located on the air tank. The remaining Pressure Switch connection should be attached to ground. Secure the end to any metal body or to the negative side of the vehicle’s battery. The ground connection should be rust and paint free. Your compressor is now set for use and will turn on automatically when air pressure in the air tank falls. When air pressure reaches maximum PSI, it will turn off. If the compressor fails to reach the maximum air pressure of the tank, which is the Pressure Switch’s cut OFF pressure, check all air connections for leaks. While the compressor is pumping, use soapy water or any bubble solution to perform this check. In case the leak remains after tightening, re-apply thread sealant. Make sure that electrical and fitting connections are regularly inspected, cleaned and tightened when needed. Make sure mounting screws are regularly tightened if needed. Compressor features a washable air filter which should be cleaned using any mild form of liquid soap every two months if it gets dusty. Just remove the front cover of the filter’s housing to reach it. Replacement time frames depend on the operating environment and how often it is used. Clean dirt and dust from heat spreader and motor housing of the compressor. The motor of the air compressor has a maintenance-free lasting lubricant. SOLUTIONS TO COMMON ISSUES. Solution 1: Check all switches to make sure they are ON. Solution 2: Check the fuse; if blown, disconnect compressor from power and replace the fuse. Solution 3: Allow compressor to cool off for 30-60 minutes. Solution 4: Check pressure switch, replace if damaged or inoperable. Issue: Excessive moisture in horn or safety valve. Solution 1: Depressurize and drain the tank. Solution 2: Relocate the on-board air system to a drier location. Issue: Continual cutting-off of Thermal overload protection. Solution 1: Relocate the on-board air system to a drier, cooler location. Solution 2: Replace the compressor. Issue: Excessive vibration or noise. Solution 1: Tighten system components. Issue: Loss of pressure of tank when compressor is shut off. Solution 1: Tighten drain cock. Solution 2: Examine air and check valves and replace if damaged or leaking. Solution 3: Use soap and water solution on air connections, and tighten connections or repair leaks where needed. Olution 4: Replace safety valve if present in the tank, it may be defective. Issue: Compressor runs continuously and has low air flow. Solution 1: Decrease the frequency of use. Solution 2: Use soap and water solution on air connections, and tighten connections or repair leaks where needed. Solution 3: Clean or replace the air filter element if it is clogged. Solution 4: Replace compressor. Make sure you never attempt to disassemble this horn kit’s electrical components. Never use your bare hands to any part of the compressor immediately after or during use. Avoid operating this product in an area with risk of falling or submergence into a liquid (water). Do not reach out for or touch any component that has fallen or been submerged into water. Make sure you set up in areas with good ventilation. Never sound the air horn anywhere near your ear(s) or that of another person. Make sure your battery ground is detached before getting your installation started. The specific voltage requirement for this horn kit is 12 volt DC, therefore installation must be done to a DC power source of 12 volts. 14.210.27.1. The images shown are not the actual item and are for your reference only. Service transit time is provided by the carrier and excludes weekends and holidays. Transit times may vary, particularly during the holiday season. There are NO EXCEPTIONS! FEEDBACK IS VERY IMPORTANT TO US. It is impossible to address issues if we do not know about them! Transfer Case Shift Motor. Secondary Air Injection Pump. Center Console Organizer Parts. ATV Brake Master Cylinder. Fuel Injector Wiring Harness. Mass Air Flow Sensor. Splash Guards & Mud Flaps. Brake Disc Rotors and Pads. Brake Pads & Rotor & Caliper. Brake Pads & Calipers. Light Bar Mount Bracket. LED 3RD Brake Light. Cylinder Head Gasket Sets. 4 Pcs wheel hub bearing. UTV & ATV Brake System Parts. Kevlar Carbon Brake Pads. Pivot Brake Clutch Lever. Cooling Fans and Fan Clutches. Brake Rotors Pads & Drum Shoe. Drop Spindle Lowering Kit. Rear Window Louver Cover. C Notch & Flip Kit. Body Side Door Moulding. Motorcycle Carburetor & Parts. Hinge for Chevy GMC C/K Rear 15691087 15691088 Tailgate Mounted Tail Gate. BLACK HOUSING LED THIRD 3RD TAIL BRAKE LIGHT LAMP FOR 97-03 FORD F150/97-99 F250. For 04-08Ford F-150 06-08Lincoln Mark Clear LED 3RD THIRD BRAKE REAR TAIL LIGHTS. Pack of 8 Square Ignition Coil For CHEVY GMC CADILLAC 5.3L 6.0L 8.1L 4.8L UF271. 6 Ignition Coil Pack For Nissan Altima Maxima Quest Murano 3.5L V6 UF349 C1406. 2× Ignition Coil For Ford Ranger 2.3L 2.5L F150 Expedition Lincoln Mercury FD487. L+R For 99-07 Ford F250/F350/F450/F550 Power Heated Turn Signal Tow Side Mirrors. The item “Air Compressor For Train Air Horns Air Suspension Kit Silver Heavy Duty With NPT” is in sale since Monday, October 4, 2021. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Interior\Steering Wheels & Horns”. The seller is “vap-autoparts” and is located in Ontario, California. This item can be shipped to United States.
  • UPC: Does not apply
  • Brand: ignitionco
  • Manufacturer Part Number: IG169895S01
  • Type: Horn
  • Part Type: Air Compressor
  • Horn Type: High Pressure Air
  • Material: Metal
  • Fitment Type: Direct Replacement
  • Color: Silver
  • Warranty: 1 Year
  • Placement on Vehicle: Left
  • Package Size(inch): 14.2*10.2*7.1
  • Package Weight: 12.57LB
  • Voltage: 12V

Air Compressor For Train Air Horns Air Suspension Kit Silver Heavy Duty With NPT
Continue Reading

150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4” Hose

150-PSI-Air-Compressor-for-Car-Truck-Train-Horns-Bag-Suspension-with-1-4-Hose-01-hq
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose

150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
12V 150Psi Air Compressor 1/4 Hose Kit For Car Truck Train Horns Suspension Specification: Condition: Brand New!! Features: -Oil-less Design -Moisture and Dust Resistant -Anodized Aluminum Alloy Cylinder -Automatic Reset Thermal Overload Protector -Mounting Plates with Vibration Isolators -¼ NPT Stainless Steel Braided Leader Hose -Intake Filter Assembly -Insulated Wiring with Connectors Package Incldues: 1 x Air Compressor 4 x Flat Head Screws 8 x Mounting Pieces 4 x Nuts 4 x Small Steel Rings 1 x Rubber Ring 1 x Fuse 1 x Safety Valve Note: 1. We provide clear pictures, measurements where possible. Please check as much as possible to make sure the item is the one that you need. Please allow 0.5-1 inch difference due to manual measurement. There are no instructions included in this kit. We will provide help as much as possible. The item “150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4” Hose” is in sale since Saturday, September 25, 2021. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Interior\Steering Wheels & Horns”. The seller is “unopery” and is located in Shenzhen. This item can be shipped worldwide.
  • Brand: Unbranded
  • Manufacturer Part Number: fQh8348613
  • Type: Compressor
  • Placement on Vehicle: Front,Rear
  • Warranty: 1 Year
  • Fitment Type: Direct Replacement
  • Horn Type: Electric
  • Color: Silver
  • Size: 21cm x 15.2cm (LxH)
  • Hose Length: 58cm
  • Voltage: 12V
  • Maximum Working Pressure: 150 PSI
  • Duty Cycle: 25% @ 100 PSI
  • Amperage Draw: 20A
  • Flow Rate: 1.9CFM @ 0 PSI

150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
Continue Reading

150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4” Hose

150-PSI-Air-Compressor-for-Car-Truck-Train-Horns-Bag-Suspension-with-1-4-Hose-01-dozc
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose

150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
12V 150Psi Air Compressor 1/4 Hose Kit For Car Truck Train Horns Suspension Specification: Condition: Brand New!! Features: -Oil-less Design -Moisture and Dust Resistant -Anodized Aluminum Alloy Cylinder -Automatic Reset Thermal Overload Protector -Mounting Plates with Vibration Isolators -¼ NPT Stainless Steel Braided Leader Hose -Intake Filter Assembly -Insulated Wiring with Connectors Package Incldues: 1 x Air Compressor 4 x Flat Head Screws 8 x Mounting Pieces 4 x Nuts 4 x Small Steel Rings 1 x Rubber Ring 1 x Fuse 1 x Safety Valve Note: 1. We provide clear pictures, measurements where possible. Please check as much as possible to make sure the item is the one that you need. Please allow 0.5-1 inch difference due to manual measurement. There are no instructions included in this kit. We will provide help as much as possible. The item “150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4” Hose” is in sale since Monday, August 30, 2021. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Interior\Steering Wheels & Horns”. The seller is “unopery” and is located in Shenzhen. This item can be shipped worldwide.
  • Brand: Unbranded
  • Manufacturer Part Number: fQh8348613
  • Type: Compressor
  • Placement on Vehicle: Front,Rear
  • Warranty: 1 Year
  • Fitment Type: Direct Replacement
  • Horn Type: Electric
  • Color: Silver
  • Size: 21cm x 15.2cm (LxH)
  • Hose Length: 58cm
  • Voltage: 12V
  • Maximum Working Pressure: 150 PSI
  • Duty Cycle: 25% @ 100 PSI
  • Amperage Draw: 20A
  • Flow Rate: 1.9CFM @ 0 PSI

150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
Continue Reading

150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4” Hose

150-PSI-Air-Compressor-for-Car-Truck-Train-Horns-Bag-Suspension-with-1-4-Hose-01-xir
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose

150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
Dear customers, We are always working hard to ensure that orders are delivered on time. But inevitably there will be a very small number of orders may be delayed due to the worsening of the epidemic. Thank you for your support! 12V 150Psi Air Compressor 1/4 Hose Kit For Car Truck Train Horns Suspension Specification: Condition: Brand New!! Features: -Oil-less Design -Moisture and Dust Resistant -Anodized Aluminum Alloy Cylinder -Automatic Reset Thermal Overload Protector -Mounting Plates with Vibration Isolators -¼ NPT Stainless Steel Braided Leader Hose -Intake Filter Assembly -Insulated Wiring with Connectors Package Incldues: 1 x Air Compressor 4 x Flat Head Screws 8 x Mounting Pieces 4 x Nuts 4 x Small Steel Rings 1 x Rubber Ring 1 x Fuse 1 x Safety Valve Note: 1. We provide clear pictures, measurements where possible. Please check as much as possible to make sure the item is the one that you need. Please allow 0.5-1 inch difference due to manual measurement. There are no instructions included in this kit. We will provide help as much as possible. The item “150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4” Hose” is in sale since Saturday, July 3, 2021. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Interior\Steering Wheels & Horns”. The seller is “unopery” and is located in Shenzhen. This item can be shipped worldwide.
  • Brand: Unbranded
  • Manufacturer Part Number: fQh8348613
  • Type: Compressor
  • Placement on Vehicle: Front,Rear
  • Warranty: 1 Year
  • Fitment Type: Direct Replacement
  • Horn Type: Electric
  • Color: Silver
  • Size: 21cm x 15.2cm (LxH)
  • Hose Length: 58cm
  • Voltage: 12V
  • Maximum Working Pressure: 150 PSI
  • Duty Cycle: 25% @ 100 PSI
  • Amperage Draw: 20A
  • Flow Rate: 1.9CFM @ 0 PSI

150 PSI Air Compressor for Car Truck Train Horns Bag Suspension with 1/4'' Hose
Continue Reading